This post listed below on the subject of How to Install a Bathtub is seriously attention-grabbing. Read it for your own benefit and see what you think about it.
Installing a bath tub isn't exactly rocket science, yet it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move quickly; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have actually certified yourself for the job and also are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed task, it is better to consider utilizing one prior to you start. Opportunities are you might need a specialist plumber to make tube links.
This write-up will help you install a new tub in your shower room if you have actually currently bought a new tub and don't need to alter the plan of your previous water system pipelines.
Your devices and also product list should comprise the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, position the bath tub in the required setting. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub till the spirit level reads level.
To set up taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bath tub needs to wait till the bath tub has actually been made use of a minimum of when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in position with the producer offered backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former type needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can crack rather early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our post about How to Install a Bathtub Yourself. Thanks a lot for spending some time to read our posting. Are you aware of another individual who is fascinated with the niche? Be sure share it. Thanks for your time. Don't hesitate to come visit our site back soon.
Book Today